Deks Olje 1
Prepare
wood:
The surface
must be clean, dust free and DRY
Deks Olje 1 is a hard drying, deep penetrating oil that
will protect your wood against water ingress and the harsh effects of the sun.
It will bring out the grain and natural colour of the wood and the finish will
be MATT.
*NB Even though Deks Olje 1 is hard
drying, Deks Olje 1 is an OIL it is not a varnish so please read the suggested
maintenance sections carefully
Work in
small areas:
Coat the
surface using a brush or roller with Deks Olje 1
As soon as
the oil has soaked into the wood (the glossy wet look will start to disappear –
we are talking about one to ten minutes time span) apply another coat of Deks Olje 11 over the area.
Continue
applying coats of Deks Olje 1 until
you have completely saturated the wood.
How many coats you have to apply before
full penetration is achieved depends on the woods porosity and the fineness of
the finished surface.
COMPLETE
SATURATION: You
will know that the wood is fully saturated when after 10 to 15 minutes after
having coated the surface, the wood is still glossy wet looking.
IMPORTANT:
NOW YOU MUST TAKE A LINT-FREE DRY
CLOTH AND WIPE THE SURFACE YOU HAVE BEEN SATURATING.
WIPE
OFF ALL EXCESS OIL.
DO
NOT LEAVE ANY AREA WET LOOKING.
Move onto
the next small area for saturating and repeat the process until the entire
surface you wish to saturate has been covered.
NB
Deks Olje #1 IS AN OIL and is NOT “NO
MAINTENANCE” it is a “LOW MAINTENANCE” product
FOR EASY
TROUBLE FREE MAINTENANCE. (Every One, two or three months depending on your
situation **See notes on Criteria**)
Before your surface starts to become dull, clean the surface (a normal
wash rinse and dry). This will remove any surface dirt and grease. Then with a
lint free cloth dampened down with Deks Olje 1 wipe down the cleaned
surface. After about 5-10 minutes go back and buff the surface with a dry lint
free cloth. This will remove any excess oil and bring back a natural lustre to
the wood
When your woodwork begins to look a
little bit dull
Clean the
surface well as above and rub down lightly with an AllBright 3M pot scourer
over the area to be touched up. Apply another coat of Deks Olje 1 with a brush
over the area that has gone dull allow the oil to saturate for 5-10 minutes
then wipe off any excess oil and allow to dry. Then Buff. Your wood will be
back to it’s beautiful self.
If your woodwork is starting
to go grey and or looking very dry and dull in places.
This
means that while there will still be some oil deep in the wood your surface
wood is now back to bare wood. You will need to clean the surface with Dekswood Cleaner to remove any grey, oxidised wood and bring back the original
brightness and colour back to your wood. Rinse well and then allow the wood to
thoroughly dry and then follow the Deks Olje 1 Re-Saturation process
over the whole area making certain that the exposed areas are properly
saturated. Once you have completed the saturation process wipe off the excess
oil with a dry, lint free cloth and buff
Deks Olje #2
Deks Olje #2 will give you a HIGH GLOSS, hard drying oil finish, that once applied and
maintained properly will not crack, peel
or flake & should never require sanding again.
**REMEMBER Even though Deks Olje #2 is hard
drying and looks like a gloss varnish, Deks Olje #2 is an OIL it is important
that you read the suggested mainDeks Olje #2tenance sections carefully so as to get the
best short and long term results
To prepare
the wood
FIRST: THE WOOD MUST BE FULLY SATURATED WITH Deks Olje #2
Apply Deks Olje 1 as above and allow to
completely dry before applying Deks Olje #2 (about 48 hours)
Remove all
traces of dust or dirt with a lint free cloth.
Apply the
first coat of Deks Olje #2 over the
entire surface to be coated. Leave to dry for at least 24- hours
Once dry
and before applying the next coat make sure that the surface is free of any
dust or dirt.
REMEMBER: any dust or dirt left on the surface will be
trapped there as each layer of oil dries to a hard durable finish
Apply each
further coat as above allowing GOOD
drying time between each coat
2 Coats
should give a Deep high gloss finish 3-4 Coats will give you an extra
deep HIGH GLOSS FINISH
NB
Deks Olje #2 is an OIL and is NOT “NO
MAINTENANCE” it is a “LOW MAINTENANCE” product
For EASY
TROUBLE FREE MAINTENANCE. (Every One, two or three months depending on your
situation **See notes on Criteria**)
Before your surface
starts to become dull
Clean the
surface (a normal wash rinse and dry). This will remove any surface dirt and
grease. Then with a lint free cloth dampened down with Deks Olje #2 wipe down the cleaned surface. Allow to dry
When your woodwork begins to look a
little bit dull
Clean the
surface well and rub down lightly with a soft cloth over the area
to be touched up. With a brush apply another coat of Deks Olje #2 over the area that has gone dull and allow to dry. The
touched up area will blend in Perfectly & your wood will be back to it’s
beautiful self.
If your woodwork is starting
to go grey and or looking very dry and dull in places.
This
means that while there will still be some Deks Olje 1 oil deep in the wood
your surface wood is now back to bare wood. You will need to Clean the surface
with Dekswood Cleaner and an Allbright 3M scourer this will remove any grey
oxidised wood and any loose, damaged Deks Olje #2. It will also bring back the
original brightness and colour back to your wood. Rinse well and thDeks Olje #2en allow the
wood to thoroughly dry and then follow the Deks Olje 1 Re-Saturation
process over the exposed bare wood areas making certain that the exposed areas
are properly saturated. Once you have completed the saturation process wipe off
the excess oil with dry lint free cloth. Allow to dry for at least 24hrs and
then re-apply
Deks Olje #2 over the whole area with 2,3 or 4 coats as needed.
No comments:
Post a Comment